畢業論文

打賞
當前位置: 畢業論文 > 土木工程 >

寧波大學五層辦公樓建筑結構設計+CAD圖紙

時間:2019-05-31 22:42來源:畢業論文
寧波大學辦公樓,其中包括建筑設計和結構設計兩部分。建筑部分:首先初步方案的確定,包括柱距、層高和房間功能的確定。縱向柱距分別為6.6m;3m;6.6m;6.6m,橫向柱距分別為8.4*7

摘要: 本設計為寧波大學辦公樓,其中包括建筑設計和結構設計兩部分。建筑部分:首先初步方案的確定,包括柱距、層高和房間功能的確定。縱向柱距分別為6.6m;3m;6.6m;6.6m,橫向柱距分別為8.4*7m。建筑底層層高3.9m,其余層3.6m,共五層,建筑總面積5317.2m2 。建筑功能包括大小辦公室、會議室、會客室、多功能展廳、活動室等;各層設樓梯兩部,男女衛生間各一間。確定方案之后,通過天正軟件完成了各層平面圖,屋面排水圖,正立面、側立面圖,剖面圖以及節點詳圖的繪制。35818
結構部分:首先確定結構形式采用現澆鋼筋混凝土框架結構,屋蓋及樓蓋采用現澆式結構。然后進行梁板柱尺寸、混凝土強度及其鋼筋等級的確定,接下來就開始使用PKPM軟件繪制結構平面布置圖。等完成主次梁的布置,則開始樓屋面荷載計算以及梁間荷載的計算并將其輸入軟件。之后通過軟件就能看到電算的板配筋結果,再挑選個別板格進行手算配筋,將手算的結果與電算配筋相比較。隨后我挑選了11軸的一榀框架來計算它的荷載并與PK文件形成的一榀框架荷載進行比較。緊接著將電算的梁柱內力結果輸入Excel表進行內力組合,最后選用組合出的最大內力進行梁柱配筋計算。完成了一榀框架的計算,我開始了對樓梯的配筋,又在JCCAD中繪制的柱下獨立基礎。最后完成了梁板柱平法施工圖、基礎施工圖及樓梯配筋圖的繪制。
畢業論文關鍵詞: 建筑設計;結構設計;框架;施工圖
The building structure design for office building  of Ningbo university
[Design illustration]: This design for the office building of Ningbo university, including the architectural design and structural design of two parts.

源¥自%六:維;論-文'網=www.aftnzs.live


About building part: first of all,the determination of preliminary scheme, including column spacing, height and  room features.Vertical column spacing are 6.6 m;3 m;6.6 m and 6.6 m, the horizontal column spacing were 8.4*7 m.The underlying layer height is 3.9 m, the rest of the layer is 3.6 m, a total of five layers,a total construction area of 5317.2 m2.Architectural features include the office, conference room, reception room, multi-purpose hall, activity room etc.;Each floor  is provided with a staircase two, male and female toilet each one.After determine the scheme, I completed the floor plan of each layer, and roofing drainage plan, facade, side elevation, section and detail drawings.
About the structure part: firstly I determine the structure using cast-in-place reinforced concrete frame structure, roof and floor cast-in-situ structure. And then I determine the slab column size, concrete strength and steel grade, then begin to draw the structure layout using PKPM software. Completed primary and secondary beam arrangement, I begin building roof load calculation and calculation of beam between the load and the input software. The software will be able to see the board computer reinforcement results, then select the inpidualpanels to hand calculation reinforcement, will hand count results and computerized reinforcement comparison. A framework for load then I picked out aframe shaft to calculate its load and formed with the PK file comparison. Then the beam column internal force result computer input Excel combination of internal forces, the final selection of maximum internal force combination of beam reinforcement calculation. The calculation of a frame, I started the reinforcement on the stairs, independent foundation under column drawing in JCCAD. Finally I complete the drawing method of construction drawing, Liang Banzhu foundation construction drawing and stair reinforcing bars chart.
Keywords:  building design;structure design;a frame structure;construction drawing 源¥自%六:維;論-文'網=www.aftnzs.live
目錄
1 建筑方案設計    1
1.1 設計依據    1
1.1.1 相關規范:    1 寧波大學五層辦公樓建筑結構設計+CAD圖紙:http://www.aftnzs.live/gongcheng/20190531/33944.html
------分隔線----------------------------
推薦內容
双色球走势图带连线