畢業論文

打賞
當前位置: 畢業論文 > 外文文獻翻譯 >

注塑模具的設計與熱分析英文文獻和中文翻譯

時間:2019-04-26 19:45來源:畢業論文
Abstract This paper presents the design of a plastic injection mould for producing warpage testing specimen and performing thermal analysis forthe mould to access on the effect of thermal residual stress in the mould. The technique, theory,

Abstract This paper presents the design of a plastic injection mould for producing warpage testing specimen and performing thermal analysis forthe mould to access on the effect of thermal residual stress in the mould. The technique, theory, methods as well as consideration neededin designing of plastic injection mould are presented. Design of mould was carried out using commercial computer aided design softwareUnigraphics, Version 13.0. The model for thermal residual stress analysis due to uneven cooling of the specimen was developed and solvedusing a commercial ?nite element analysis software called LUSAS Analyst, Version 13.5. The software provides contour plot of temperaturedistribution for the model and also temperature variation through the plastic injection molding cycle by plotting time response curves. Theresults show that shrinkage is likely to occur in the region near the cooling channels as compared to other regions. This uneven cooling effectat different regions of mould contributed to warpage.© 2005 Elsevier B.V. All rights reserved.Keywords: Plastic Injection mould; Design; Thermal analysis 1. IntroductionPlastic industry is one of the world’s fastest growingindustries, ranked as one of the few billion-dollar industries.34822
Almost every product that is used in daily life involves theusage of plastic and most of these products can be producedby plastic injection molding method [1]. Plastic injectionmolding process is well known as the manufacturing processto create productswith various shapes and complex geometryat low cost [2].The plastic injection molding process is a cyclic process.There are four signi?cant stages in the process. These stagesare ?lling, packing, cooling and ejection. The plastic injec-tion molding process begins with feeding the resin and theappropriate additives fromthe hopper to the heating/injectionsystemof the injection plastic injectionmoldingmachine [3].This is the “?lling stage” in which the mould cavity is ?lledwith hot polymermelt at injection temperature.After the cav-ity is ?lled, in the “packing stage”, additional polymermelt ispacked into the cavity at a higher pressure to compensate theexpected shrinkage as the polymer solidi?es. This is followed by “cooling stage” where the mould is cooled until the part issuf?ciently rigid to be ejected. The last step is the “ejectionstage” in which the mould is opened and the part is ejected,after which the mould is closed again to begin the next cycle[4].The design and manufacture of injection molded poly-meric parts with desired properties is a costly process domi-nated by empiricism, including the repeated modi?cation ofactual tooling. Among the task of mould design, designingthe mould speci?c supplementary geometry, usually on thecore side, is quite complicated by the inclusion of projectionand depression [5].In order to design a mould, many important designingfactors must be taken into consideration.

源`自*六)維[論*文'網www.aftnzs.live


These factors aremould size, number of cavity, cavity layouts, runner systems,gating systems, shrinkage and ejection system [6].In thermal analysis of the mould, the main objective isto analyze the effect of thermal residual stress or molded-instresses on product dimension. Thermally induced stressesdevelop principally during the cooling stage of an injectionmolded part, mainly as a consequence of its low thermalconductivity and the difference in temperature between themolten resin and the mould. An uneven temperature ?eldexists around product cavity during cooling [7]. During cooling, location near the cooling channel experi-ences more cooling than location far away from the coolingchannel. This different temperature causes the material toexperience differential shrinkage causing thermal stresses.Signi?cant thermal stress can causewarpage problem. There-fore, it is important to simulate the thermal residual stress ?eldof the injection-molded part during the cooling stage [8].Byunderstanding the characteristics of thermal stress distribu-tion, deformation caused by the thermal residual stress canbe predicted.In this paper the design of a plastic injection mould forproducingwarpage testing specimen and for performing ther-mal analysis for the mould to access on the effect of thermalresidual stress in the mould is presented.2. Methodology2.1. Design of warpage testing specimenThis section illustrates the design of the warpage testingspecimen to be used in plastic injection mould. It is clearthat warpage is the main problem that exists in product withthin shell feature. Therefore, the main purpose of the prod-uct development is to design a plastic part for determiningthe effective factors in the warpage problem of an injection-moulded part with a thin shell.The warpage testing specimen is developed from thinshell plastics. The overall dimensions of the specimen were120mmin length, 50mminwidth and 1mmin thickness.Thematerial used for producing the warpage testing specimenwas acrylonitrile butadiene stylene (ABS) and the injectiontemperature, time and pressure were 210 ?C, 3 s and 60MPa,respectively. Fig. 1 shows the warpage testing specimen pro-duced.2.2. Design of plastic injection mould for warpagetesting specimenThis section describes the design aspects and other consid-erations involved in designing the mould to produce warpagetesting specimen. 注塑模具的設計與熱分析英文文獻和中文翻譯:http://www.aftnzs.live/fanyi/20190426/32516.html
------分隔線----------------------------
推薦內容
双色球走势图带连线